The content below on the subject of How to Install a Bathtub Yourself is without a doubt enjoyable. Have a go and draw your own ideas.
Setting up a bath tub isn't exactly brain surgery, but it does call for solid plumbing, woodworking, and also often, tiling abilities. Replacing an old bathtub with a new one is likewise a moderately tough task. If the old bathtub is conveniently easily accessible, the project can move easily; if you have to open up a wall surface to eliminate the old tub and also position the brand-new bathtub, the task is much harder. In either instance, the project is within a residence handyman's abilities, although you will require an assistant to vacate the old bathtub and embeded in the brand-new one. Ensure you have certified yourself for the work and also are comfortable attempting it. Rather than employing a contractor to take over a halfway-completed project, it is much better to think about utilizing one before you begin. Possibilities are you might need an expert plumber to make tube links.
This article will certainly assist you set up a new bathtub in your washroom if you have currently acquired a brand-new bathtub and also don't need to change the arrangement of your previous supply of water pipelines.
Your tools and product list should consist of the following:
Planning for the Installation
First of all, the supporting structure supplied with the bathroom should be fitted (if needed) according to the maker's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to see to it that if the faucet includes a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also practical to fit a supporting plate under the faucets system to avoid stress on the bathtub.
Fit the flexible faucet adapters to the bottom of the two taps making use of 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet through the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you use every one of the provided washing machines.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to currently be ready to be fitted in its last placement.
Removing Old Touches
If you require to change old faucets with new ones as a part of your installment, after that the first thing you need to do is separate the water supply. After doing so, activate the faucets to drain pipes any kind of water remaining in the system. The procedure of eliminating the existing faucets can be rather problematic because of the limited accessibility that is typically the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the faucets. Have a fabric all set for the continuing to be water that will originate from the pipelines. Once the supply pipelines have been eliminated, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from turning during this process. When the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any kind of old securing substance.
Prior to proceeding to fit the new taps, compare the pipeline connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new taps to fit.
Mounting the Bathtub
Utilizing both wood boards under its feet, position the bath tub in the needed position. The wood boards are practical in uniformly spreading out the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four small factors.
The following objective is to make certain that the bath tub is leveled all round. This can be achieved by inspecting the spirit level and adjusting the feet on the bathtub up until the spirit level reviews degree.
To set up taps, fit the bottom of the outermost adaptable faucet port to the suitable supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Activate the water system and inspect all joints and new pipework for leakages as well as tighten them if needed. Fill the bathtub and likewise check the overflow outlet as well as the typical electrical outlet for leakages.
Lastly, deal with the bathroom paneling as explained in the maker's user's manual. Tiling and sealing around the tub needs to wait till the bath tub has been used at least when as this will resolve it into its last position.
Suitable New Taps
If the tails of the new taps are plastic, after that you will require a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, position the faucet in the mounting opening in the bath/basin guaranteeing that the washers are in area in between the tap as well as the sink. Secure the tap in place with the maker provided backnut. As soon as the faucet is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal tap connectors. The previous kind needs to be connected to the tap ends initially, tightening just by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the area where the bathroom satisfies the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can move enough to crack a rigid seal, triggering the water to pass through the wall in between the bathroom as well as the tiling, leading to complications with dampness and feasible leaks to the ceiling below.
You can pick from a range of coloured sealers to assimilate your fixtures and installations. They are marketed in tubes as well as cartridges, as well as are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a larger void to load, you can load it with twists of drenched paper or soft rope. Remember to constantly load the bath tub with water prior to securing, to enable the motion experienced when the bathtub remains in use. The sealer can fracture fairly early if you do not think about this movement before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise quickly available on the market. It is recommended to fit the floor tiles utilizing waterproof or water resistant sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was shown that write-up about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround through an acquaintance on our other website. Appreciated our post? Please share it. Let another person find it. We treasure reading our article about How to Install a Bathtub.
Urgent plumbing? Call.